mirror of
https://github.com/Grasscutters/mitmproxy.git
synced 2024-11-23 16:17:49 +00:00
102 lines
3.1 KiB
ReStructuredText
102 lines
3.1 KiB
ReStructuredText
.. _transparent-dhcp:
|
|
|
|
Transparently proxify virtual machines
|
|
======================================
|
|
|
|
This walkthrough illustrates how to set up transparent proxying with mitmproxy.
|
|
We use VirtualBox VMs with an Ubuntu proxy machine in this example,
|
|
but the general *Internet <--> Proxy VM <--> (Virtual) Internal Network* setup can be applied to
|
|
other setups.
|
|
|
|
1. Configure Proxy VM
|
|
---------------------
|
|
|
|
On the proxy machine, **eth0** is connected to the internet. **eth1** is connected to the internal
|
|
network that will be proxified and configured to use a static ip (192.168.3.1).
|
|
|
|
VirtualBox configuration
|
|
^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
.. image:: transparent-dhcp/step1_vbox_eth0.png
|
|
|
|
.. image:: transparent-dhcp/step1_vbox_eth1.png
|
|
|
|
VM Network Configuration
|
|
^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
.. image:: transparent-dhcp/step1_proxy.png
|
|
:align: center
|
|
|
|
2. Configure DHCP and DNS
|
|
-------------------------
|
|
|
|
We use dnsmasq to provide DHCP and DNS in our internal network.
|
|
Dnsmasq is a lightweight server designed to provide DNS (and optionally
|
|
DHCP and TFTP) services to a small-scale network.
|
|
|
|
- Before we get to that, we need to fix some Ubuntu quirks:
|
|
**Ubuntu >12.04** runs an internal dnsmasq instance (listening on loopback only) by default
|
|
`[1] <https://www.stgraber.org/2012/02/24/dns-in-ubuntu-12-04/>`_. For our use case, this needs
|
|
to be disabled by changing ``dns=dnsmasq`` to ``#dns=dnsmasq`` in
|
|
**/etc/NetworkManager/NetworkManager.conf** and
|
|
|
|
if on Ubuntu 16.04 or newer running:
|
|
|
|
>>> sudo systemctl restart NetworkManager
|
|
|
|
if on Ubuntu 12.04 or 14.04 running:
|
|
|
|
>>> sudo restart network-manager
|
|
|
|
afterwards.
|
|
- Now, dnsmasq can be be installed and configured:
|
|
|
|
>>> sudo apt-get install dnsmasq
|
|
|
|
Replace **/etc/dnsmasq.conf** with the following configuration:
|
|
|
|
.. code-block:: none
|
|
|
|
# Listen for DNS requests on the internal network
|
|
interface=eth1
|
|
# Act as a DHCP server, assign IP addresses to clients
|
|
dhcp-range=192.168.3.10,192.168.3.100,96h
|
|
# Broadcast gateway and dns server information
|
|
dhcp-option=option:router,192.168.3.1
|
|
dhcp-option=option:dns-server,192.168.3.1
|
|
|
|
Apply changes:
|
|
|
|
if on Ubuntu 16.04 or newer:
|
|
|
|
>>> sudo systemctl restart dnsmasq
|
|
|
|
if on Ubuntu 12.04 or 14.04:
|
|
|
|
>>> sudo service dnsmasq restart
|
|
|
|
Your **proxied machine** in the internal virtual network should now receive an IP address via DHCP:
|
|
|
|
.. image:: transparent-dhcp/step2_proxied_vm.png
|
|
|
|
3. Redirect traffic to mitmproxy
|
|
------------------------------------------
|
|
|
|
To redirect traffic to mitmproxy, we need to add two iptables rules:
|
|
|
|
.. code-block:: none
|
|
|
|
sudo iptables -t nat -A PREROUTING -i eth1 -p tcp --dport 80 -j REDIRECT --to-port 8080
|
|
sudo iptables -t nat -A PREROUTING -i eth1 -p tcp --dport 443 -j REDIRECT --to-port 8080
|
|
|
|
4. Run mitmproxy
|
|
----------------
|
|
|
|
Finally, we can run mitmproxy in transparent mode with
|
|
|
|
>>> mitmproxy -T
|
|
|
|
The proxied machine cannot to leak any data outside of HTTP or DNS requests.
|
|
If required, you can now :ref:`install the mitmproxy certificates on the proxied machine
|
|
<certinstall>`.
|